Microstructure and Grain Size Optimization in Friction Stir Welding of Al 6061 to Cu Using the Taguchi Method

Investigation of the effect of stress ratio on fatigue life in a microstructure-sensitive fatigue model for ultimate grain refinement and initiation grain refinement of high-speed friction stir welding of AA6061-T6 to Cu

Experimental and numerical study of temperature and residual stress in two-pass friction stir welding of dissimilar alloys 6061-T6 to 5083

Microstructure-sensitive fatigue modeling of High-Speed Friction Stir Butt Welding of dissimilar joints AA6061-T6 to copper

Effects of friction stir welding of 6061-T6 To 5083-H11 aluminum alloys reinforced with Al2O3 on microstructure, hardness, and wear resistance

Microstructure modeling of dynamic recrystallization in joining dissimilar , Al to Cu sheets by high-speed friction stir butt welding

Investigating the Effect of Al2O3 Nanoparticles on the Microstructure and Corrosion Resistance of Dissimilar Friction Stir Welding in Aluminum Alloys 6061-T6 and 5083

Experimental and Numerical Investigation of Single and Double Pass Friction Stir Welding of Dissimilar Aluminum Alloys 6061‑T6 and 5083 with the Addition of Al2O3

Optimization of friction stir spot welding parameters of AA6061/Al2O3 using response surface methodology

Experimental and Numerical Study: Friction Stir Welding on Three-layer Sheets AL 6061-T6 with the Middle Layer Ti–6Al–4V

Investigating the Effects of Defects and the Effect of Geometric Anisotropy in Stainless Steel Pipes: Phased Array Ultrasonic Test, SH-wave

Experimental investigation on mechanical properties affected by dissimilar friction stir spot welding of aluminum 6061-T6 alloy to copper

A Review of Ultrasonic Testing Applications in Spot Welding: Defect Evaluation in Experimental and Simulation Results

Optimization in the Resistant Spot-Welding Process of AZ61 Magnesium Alloy

Experimental and numerical study on failure of friction stir welded joint in conventional and bobbin tool using GTN model

Automotive Fire Control by Designing and Launching a New Intelligent System: Experimental Results, Automotive Notification Design, New Design Comparison Chart

Detection of a new method for corrosion defects in turbine impeller blades by non-destructive testing

Experimental and numerical study on failure of resistance spot welded AA6061-T6 joint under tensile-shear test using GTN model

Investigation of Welding Parameters Effects on Residual Stresses of Resistance Spot Welding of AZ31 Alloy

Investigation the effect of bobbin tool geometry in friction stir welding of aluminum alloy 6061-T6

Optimization of AZ61 Mg Alloy Resistance Spot Welding using Response Surface Method

Investigating the effect of material properties on simulation of Mg alloy resistance spot welding process

Residual Stresses in Resistance Spot Welded AZ61 Mg Alloy

Optimization of welding parameters in resistance spot welding of AZ61 Mg alloy

Forming of Multilayer Sheet Metal by Drawing Process: An Analysis and FEM Simulation

Investigation fatigue behavior of spot welded Al 6061-T6 under tensile-shear loading

Effect of Variable Valve Timing to Reduce Specific Fuel Consump tion in HD Diesel Engine

Investigation the effects of welding parameters on nugget size in Mg alloys resistance spot welded joints

Thermal contact conductance effect in modeling of resistance spot welding process of aluminum alloy 6061-T6

Investigation the effect of ecltrode force on residual stresses relised in resitance spot welding of Al alloy

PREDICTION OF THE NUGGET SIZE IN RESISTANCE SPOT WELDING WITH A COMBINATION OF A FINITE-ELEMENT ANALYSIS AND AN ARTIFICIAL NEURAL NETWORK

On Residual Stresses in Resistance Spot-Welded Aluminum Alloy 6061-T6: Experimental and Numerical Analysis

An approach to reduce experiments quantity: A case study on thermal aspects of creep feed grinding process

An approach in prediction of failure in resistance spot welded aluminum 6061-T6

Creep feed grinding optimization by an integrated GA-NN system

Microstructure and Grain Size Optimization in Friction Stir Welding of Al 6061 to Cu Using the Taguchi Method

Experimental and Numerical Analysis of Friction Stir Welding of Three-Layer Aluminum with a Titanium Intermediate Layer

Experimental investigation of the effects of tool geometry on the microstructure and hardness of friction stir welded 6061-T6 aluminum

Experimental Investigation on The Quality of Chemical Coating on Cu

Optimization on the welding parametrs of friction spot welding of Al 6061 with alumina nanoparticles using RSM

Experimental and Thermomechanical Finite Element Investigation on The Weding Area in Al 6061-T6-Cu FSW

Experimental investigation on FSW's parameters effects on the quality of Al 6061-T6 joint using in marine

Optimization of affected parametrs on tensile strength of FSW using RSM

Optimizxation of welding parameters of dissimilar welding process using RSM

Experimental and nuerical investigation on FSW 0f Al6061 using bubin tool

Aluminum resistance spot welding optimization using genetic algorithm and response surface method

Fatigue life prediction in welded K-Joint

Analysis of Forming Limit Diagram in the hydromorming Proccess of T-Type tubes

Measuring nugget size of friction stir welded AZ61 using ultrasonic

Optimization of welding paramters of flux cored arc welding using genetic algorithm

Multi-objective optimization of crank-rocker mechanism using genetic algorithm

Investigation the effects of bobbin tools on tensile strength and failure of firiction welded Al 6061-T6

Investigation of mechanical strength and nugget diameter in the resitance spot welding of AZ61 magnesium alloy

Prediction of nugget size in resistance spot welding of AZ61magnesium alloy by finite element model

The Prediction of residual stresses in resistance spot welded magnesium alloy by finite element model

Otimization of stability of a vehicle by Taguchi and Carsim softwatre

Optimization of abrasive waterjet process by ANN and GA

Optimization of surface rougness during turning by ANN and GA

Investigation the effects of matris radiuos on the stresses in deep drawing

Investigation the effects of velocity and distance between rolls on thickness of sheet in cold rolling

Optimization of super austenit steel laser welding by taguchi method

Optimization of blade creep feed grinding by population algorithm

optimization of welding parameters to improve mechanical properties by genetic algorithm

Investigation effect of the timing on decreasing fuel in OM457 diesel motor

Detecting crack position by BA optimization algorithm

Investigation the effects of thermal properties on the modeling of Al6061 spot welding

The effects of thickness, cooficient of friction and pre-strain sheet stretch froming on AA1200 aluminum

Optimization of slippage parameter in axisymmetric extrusion process thorough ratating dies

Investigation the effects of the tool shape on turning process by FEM

Numerical simulation of grinding process with and without coolant and comparison with experimental and analytical models

Surface Roughness Prediction by ANN and Fuzzy Control